| 引用本文: | 于子淞,王大志,赵国新,韩伟.直驱小惯量表贴式永磁同步电机的转速脉动抑制[J].控制理论与应用,2016,33(6):832~840.[点击复制] |
| YU Zi-song,WANG Da-zhi,ZHAO Guo-xin,HAN Wei.Suppression of speed ripple for direct-drive small inertia surface permanent magnet synchronous motor[J].Control Theory and Technology,2016,33(6):832~840.[点击复制] |
|
| 直驱小惯量表贴式永磁同步电机的转速脉动抑制 |
| Suppression of speed ripple for direct-drive small inertia surface permanent magnet synchronous motor |
| 摘要点击 2811 全文点击 2155 投稿时间：2015-07-02 修订日期：2016-03-03 |
| 查看全文 查看/发表评论 下载PDF阅读器 |
| DOI编号 10.7641/CTA.2016.50578 |
| 2016,33(6):832-840 |
| 中文关键词 直驱 表贴式永磁同步电机 复合PI调速器 非线性电流测量误差 积分型模型预测控制 电压源逆变器 非线性畸变电压 |
| 英文关键词 direct-drive surface permanent magnet synchronous motor composite PI speed controller nonlinear current measurement error integral model predictive control voltage source inverter nonlinear distorted voltage |
| 基金项目 国家自然科学基金重点项目(60843007), 国家自然科学基金项目(51467017)资助. |
|
| 中文摘要 |
| 非线性电流测量误差和电压源逆变器(VSI)非线性畸变电压造成了直驱小惯量表贴式永磁同步电机(SPMSN)
的转速脉动. 本文将q轴非线性电流测量误差等效为扰动负载电流, 提出一种复合PI(CPI)调速器抑制电机转速脉动.
该调速器由传统PI调节器与偏差补偿器并联构成, 偏差补偿器用以抑制非线性负载电流. 同时, 用分段线性函数建
立IGBT关闭时间模型, 并推导了VSI非线性畸变电压表达式. 引入积分型模型预测控制(MPC)作为电流环控制器,
利用MPC的滚动时域最优预测特性抑制VSI的非线性畸变电压, 消除了零电流钳位现象. 最后, 通过仿真分析验证
了所提控制策略的有效性. |
| 英文摘要 |
| Nonlinear current measurement error and voltage source inverter (VSI) nonlinear distorted voltage produce
the speed ripple of direct-drive small inertia surface permanent magnet synchronous motor (SPMSM). This paper presents
a composite PI (CPI) speed controller to suppress the speed ripple. The proposed speed regulator consists of a conventional
PI controller shunted with a deviation compensator. The deviation compensator can reject the q axis nonlinear current
measurement error which acts as a nonlinear load current. Meanwhile, the turn-off time of IGBT is modeled by a piecewise
linear function which is used to deduce the VSI nonlinear distorted voltage. Integral model predictive control (MPC)
is introduced as current controller to suppress VSI nonlinear distorted voltage and eliminate the zero-current clamping
phenomenon. At last,the simulation results verify the feasibility of the control strategy. |